NM2-IP-4L Tilt Measuring System
Dual axis tilt measuring system
Caractéristiques principales
- Measuring range ±3° up to ±60° or 0 - 90° per axis
- Accuracy ±0,1° (up to ± 15°), 0,5% of measuring range (up to ±60°)
- Analogue output 0 … (±)10 V or 0(4) … 20 mA (4-wire-technology)
- Supply voltage 10 … 18 VDC or 18 … 30 VDC
About the NM2-IP-4L Tilt Measuring System
The dual axis industrial tilt measuring system NM2-IP-4L is the combination of a non-contact inclination sensor AccuStar®-EA and sensor adapted electronics. The measuring system is designed for precise tilt measurement in X- and Y-axis and intended for ground assembly. Available tilt measuring ranges are ±3° to ±60°. The electrical wiring is realized in 4-wire-technology. For further evaluation of the measured inclination there are different standard analogue output signals per axis available, depending on the ordered type.
The tilt measuring system is built into a robust EMC-safe die-cast aluminium enclosure (IP66), which is well suited for applications in rough and industrial environments.
Avez-vous besoin de ce capteur pour votre prochain projet?
Demandez un devis sans engagement ou envoyez-nous vos coordonnées pour une consultation gratuite et sans engagement. Nos ingénieurs commerciaux vous contacteront dans un délai maximum de 1 à 2 jours ouvrables.
Téléchargements de produits
Parlez à nos experts
Vous ne trouvez pas exactement ce que vous cherchez ? Nous proposons des capteurs et des systèmes de mesure standard, mais nous pouvons également vous aider à concevoir un capteur sur mesure ou une solution de mesure complète. N'hésitez pas à nous contacter pour obtenir des conseils ou un devis.
Parler à un expertSpécifications techniques
Spécifications | Valeur |
---|---|
Accuracy at 23°c | Up to ±15°: ±0,1°, Up to ±60°: 0,5% of measuring range, Up to ±65°: on request |
Analogue output / burden | 0 - 10 V / ±10 V, max. 1 mA (short-time short-circuit proof) 0 - 20 mA, 4 - 20 mA, max. 500 Ω |
Cross-sensitivity | < 1% up to ±60° |
Dimensions (w x h x d) | 160 x 91 x 160 mm (without EMC cable glands) |
Electrical connection | M16 x 1,5 EMC cable glands on internal spring-cage terminal blocks |
Enclosure | EMC-safe aluminium die-cast enclosure |
Frequency range (-3 db) | 2 Hz |
Number of measuring axis | 2 |
Power consumption | ca. 4 W |
Preferred measuring range | ±3°, ±5°, ±10°, ±15, ± 20, ±30, ±45°, ±60° other measuring ranges on request |
Protection class | IP66 |
Supply voltage | 10 - 18 VDC*, 18 - 30 VDC*, electronic is protected against voltage reversal |
Temperature, operating | -20 - +60 °C |
Temperature, storage | -20 to +60 °C |
Voltage insulation between supply voltage and analogue output | Galvanic isolation between supply voltage and analogue output, 200 V, higher voltage insulation on request |
Weight | 2.300 g |
Produits apparentés
Besoin d'autre chose?
NSS1-IP Tilt Measuring System
- Measuring range ±3° up to ±60° or 0 to 90°
- Switching accuracy max. 0,5%
- With 2 switching contacts
NSS2-M2-IP Tilt Measuring System
- Measuring range ±3° up to ±10°
- With 2 switching contacts per axis
- Robust EMC-safe aluminium enclosure IP66
NSZ1-IP Tilt Measuring System
- Measuring range ±3° up to ±60° or 0 to 90°
- With 2 switching contacts & switching delay
- For rough and industrial environments