ALF301 Low Range Stylus Force Sensor
Integral overload stops to protect against overloading in the vertical axis
Caractéristiques principales
- Low range stylus loadcell
- Full load range: 1 - 3N
- Tension, compression and bi-directional
- Rated output rationalised: 2mV/V
- Non-lin./hysteresis: 0.1/0.1% RL
- Dimensions (mm): Ø12 x 90
About the ALF301 Low Range Stylus Force Sensor
The ALF301 is a compact bending beam loadcell for low range force measurements. Its small diameter eases mounting problems in existing systems. All standard bi-directional loadcells are calibrated in both modes.
The loadcell has integral overload stops to protect against overloading in the vertical axis. Torsional loads about the longitudinal axis may damage the loadcell.
We are happy to design variants of this loadcell to meet your specific requirements.
Versions can be manufactured for higher temperature operation. Please consult our engineering department.
All standard ranges are manufactured in aluminium. When this loadcell is rationalized the resistors are housed in a capsule located in the loadcell cable 100mm from the free end. Capsule dimensions are Ø10mm by 57mm.
Notes
1. AL = Applied load. 3. Temperature coefficients apply over the compensated range.
2. RL = Rated load. 4. The load must be applied directly through the central loading axis.
Connections
The loadcell is fitted with 2 metres of PVC insulated 4 core screened cable type 7-1-4C.
Excitation + = Red Signal + = Yellow Screen = Orange
Excitation - = Blue Signal - = Green
Reverse the signal connections to obtain a positive signal in tension mode. The screen is not connected to the loadcell body.
Avez-vous besoin de ce capteur pour votre prochain projet?
Demandez un devis sans engagement ou envoyez-nous vos coordonnées pour une consultation gratuite et sans engagement. Nos ingénieurs commerciaux vous contacteront dans un délai maximum de 1 à 2 jours ouvrables.
Téléchargements de produits
Parlez à nos experts
Vous ne trouvez pas exactement ce que vous cherchez ? Nous proposons des capteurs et des systèmes de mesure standard, mais nous pouvons également vous aider à concevoir un capteur sur mesure ou une solution de mesure complète. N'hésitez pas à nous contacter pour obtenir des conseils ou un devis.
Parler à un expertSpécifications techniques
| Spécifications | Valeur |
|---|---|
| Bridge resistance | 350 Ω |
| Creep - 20 minutes | ±0.05% AL |
| Excitation voltage - maximum | 10V |
| Excitation voltage - recommended | 10V |
| Hysteresis | ±0.1% RL |
| Insulation resistance - minimum at 50vdc | 500MΩ |
| Load direction | Tension, compression, bi-directional |
| Measurement range | 1N, 3N |
| Non-linearity - terminal | ±0.1% RL |
| Overload - safe | 20% RL |
| Overload - ultimate | 100% RL |
| Rated output - nominal | 1.0mV/V |
| Rated output - rationalised | 0.8mV/V |
| Rationalisation tolerance (applies to single direction calibrations) | 0.5% RL |
| Repeatability | ±0.03% RL |
| Temperature effect on rated output per °c | ±0.005% AL |
| Temperature effect on zero load output per °c | ±0.01% RL |
| Temperature range - compensated | -10 to +50°C |
| Temperature range - safe | -10 to +80°C |
| Weight - nominal (excluding cable) | 18 to 20g |
| Zero load output | ±8% RL |
Produits apparentés
Besoin d'autre chose?
ALF320 Bending Beam Force Sensor
- Measuring range: 5, 10 or 50 kN
- Heavy duty binocular bending beam loadcell
- Moment rejection cantilever bracket type
ALF325 Bending Beam Force Sensor
- Measuring range: ~50 N to ~500 N
- Built to meet the needs of machine designers
- High structural stiffness
