1. Althensensors
  2. Capteurs
  3. Capteurs de position linéaire
  4. Capteurs LVDT
  5. GHSD-Series LVDT Position Sensor

GHSD-Series LVDT Position Sensor

Spring-loaded DC-LVDTs designed for a wide range of position measurement and dimensional gaging applications


Caractéristiques principales

  • Ranges of ±0.020 inch to ±2.00 inches
  • Repeatability <0.01% of FRO
  • Non-linearity less than ±0.25% of FRO
  • Coil environmentally sealed to IEC IP-68
  • ±15 V DC input, pre-calibrated 0 to ±10 V DC output

About the Spring-loaded DC-LVDT position sensor

The GHSD 750 and GHSDR series of 3/4 inch diameter spring-loaded DC-LVDTs are designed for a wide range of position measurement and dimensional gaging applications. These rugged hermetically sealed sensors are constructed entirely of stainless steel and intended for general industrial use. The coil windings are sealed against hostile environments to IEC standard IP-68. The electrical termination for the GHSD is through a sealed axial connector. The GHSDR electrical termination is through a radially mounted sealed connector, which results in a much reduced installed length. The throughbore design allows for air purging of the sensor’s bearings to remove potential contaminants. The mating connector plug is supplied with the unit.

The sensor consists of a spring loaded shaft running in a precision sleeve bearing and connected to the core of an LVDT. The use of a precision sleeve bearing results in measurement repeatability of 0.01% of full range or better. The probe shaft is fully extended by a spring exerting a nominal force of 6 to 20 ounces depending upon total range. The contact tip supplied is an AGD standard number 9 made from chrome plated hardened tool steel. It is fully interchangeable with other AGD contact tips.

Built-in electronics result in position sensors that operate from a DC input and generate a pre-calibrated DC output. The output from the GHSD 750 and GHDSR series is designed to operate with many PLCs, digital indicators, A/D converters, computer-based data processors, and QC data collection systems.

For simplified mounting the LVDT has a 1/2-20 UNF 2A thread on the front of the housing, permitting the user to install the LVDT in a mating threaded part or by using the two hex nuts furnished with the sensor. This results in a ready-to-use package for position measurements and longer range gaging applications.

Applications for GHSD-Series

  • Industrial gaging systems
  • Electronic dial indicators
  • Fabricated metal products gaging
  • Materials testing apparatus
  • Large shaft TIR measurements

Avez-vous besoin de ce capteur pour votre prochain projet?

Demandez un devis sans engagement ou envoyez-nous vos coordonnées pour une consultation gratuite et sans engagement. Nos ingénieurs commerciaux vous contacteront dans un délai maximum de 1 à 2 jours ouvrables.

Parler à un expert

Parlez à nos experts

Vous ne trouvez pas exactement ce que vous cherchez ? Nous proposons des capteurs et des systèmes de mesure standard, mais nous pouvons également vous aider à concevoir un capteur sur mesure ou une solution de mesure complète. N'hésitez pas à nous contacter pour obtenir des conseils ou un devis.

Parler à un expert

Spécifications techniques

Spécifications Valeur
Housing material Stainless steel
Measurement range 0.508 to 50.8mm
Non-linearity ±0.25% FR
Operating temperature -20°C to +70°C

Produits apparentés

Besoin d'autre chose?

GHSD-Series LVDT Position Sensor

  • Ranges of ±0.020 inch to ±2.00 inches
  • Repeatability <0.01% of FRO
  • Non-linearity less than ±0.25% of FRO
Voir le produit

GHSDR-Series LVDT Position Sensor

  • Ranges of ±0.020 inch to ±2.00 inches
  • ±15 V DC input, pre-calibrated 0 to ±10 V DC output
  • Repeatability <0.01% of FRO
Voir le produit

HC485 Series LVDT Position Sensor

  • Heavy duty digital model
  • Up To 32 Sensors On One 2-Wire Network
  • Interchangeability Without Calibration
Datasheet Voir le produit