GHSAR-A-Series LVDT Position Sensor
Airextend/spring-retract AC-LVDTs designed for a wide range of cycled position measurements
Nyckelfunktioner
- Ranges of ±0.050 inch to ±2.00 inches
- Non-linearity less than ±0.25% of FRO
- Repeatability of ±0.01% of FRO
- Radial connector with mating plug included
- Coil environmentally sealed to IEC IP-68
- Low pressure air-extend/spring-retract plunger
About the Spring-loaded air actuated LVDT
The GHSAR 750-A Series of 3/4 inch diameter airextend/spring-retract AC-LVDTs are designed for a wide range of cycled position measurement and automated dimensional gaging applications where it is necessary or desirable to move the probe out of the way between readings. These rugged hermetically sealed sensors are constructed entirely of stainless steel and intended for general industrial use. The coil windings are sealed against hostile environments to IEC standard IP-68. Electrical termination is through a radially mounted sealed connector, which results in a much reduced installed length. The mating connector plug is supplied with the unit.
The sensor consists of an air-extend/spring-retract shaft running in a precision sleeve bearing and connected to the core of an LVDT. The shaft is extended by introduction of a low-pressure (10-30 psi), clean, dry air supply, with a regulated flow, through a barbed fitting on the end of the unit for ¼ inch I.D. hose. With the release of pressure, an internal spring returns the probe to its retracted position. The use of a precision sleeve bearing results in measurement repeatability of ±0.01% of full range output or better. The contact tip supplied is an AGD standard number 9 made from black oxide hardened tool steel. It is fully interchangeable with other 4-48-threaded AGD contact tips. The combination of air actuation and a through-bore design allows for repeated purging of the sensor's bearings to remove potential contaminants.
For simplified mounting the GHSAR 750-A has a 1/2-20 UNF-2A thread on the front of the housing, permitting the user to install the LVDT in a mating threaded part or by using the two hex nuts furnished with the sensor. This results in a ready-to-use package for position measurements and longer range gaging applications.
Applications for GHSAR-A Series
- Cycled measurement functions
- Industrial gaging systems
- Fabricated metal products gaging
- Large shaft TIR measurements
Behöver du den här sensorn till ditt nästa projekt?
Begär en offert eller lämna dina uppgifter för att få mer information från en av våra experter.
Få det på ditt sätt
Inte exakt vad du letar efter? Vi erbjuder standardsensorer, men kan också hjälpa dig med en komplett skräddarsydd lösning. Kontakta oss för rådgivning eller budgetprissättning.
Prata med en expertTekniska specifikationer
Specifikation | Värde |
---|---|
Housing material | Stainless steel |
Measurement range | 1.27 to 50.8mm |
Non-linearity | ±0.25% FR |
Operating temperature | -55°C to +105°C |
Relaterade produkter
Behöver du något annat?
GHSAR-Series LVDT Position Sensor
- Ranges of ±0.050 inch to ±2.00 inches
- Repeatability of 0.01% of FRO
- Non-linearity less than ±0.25% of FRO
GHSDR-Series LVDT Position Sensor
- Ranges of ±0.020 inch to ±2.00 inches
- ±15 V DC input, pre-calibrated 0 to ±10 V DC output
- Repeatability <0.01% of FRO
GHSD-Series LVDT Position Sensor
- Ranges of ±0.020 inch to ±2.00 inches
- Repeatability <0.01% of FRO
- Non-linearity less than ±0.25% of FRO